EXACTLY HOW TO REPLACE A TUB YOURSELF: REMOVING AND REPLACING.

Exactly How to Replace a Tub Yourself: Removing and Replacing.

Exactly How to Replace a Tub Yourself: Removing and Replacing.

Blog Article

Go Deal Now

How do you actually feel about Installing A Bathtub?


How to Install a Bathtub Yourself
Mounting a bath tub isn't specifically brain surgery, yet it does call for strong plumbing, woodworking, and in some cases, tiling skills. Replacing an old bath tub with a brand-new one is additionally a reasonably tough job. If the old tub is easily available, the project can relocate rapidly; if you have to open a wall surface to get rid of the old tub and position the brand-new bath tub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly need a helper to move out the old bathtub and also set in the new one. Make sure you have actually certified on your own for the task and fit trying it. Instead of working with a service provider to take over a halfway-completed project, it is better to consider employing one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This post will help you install a brand-new bathtub in your washroom if you have actually already bought a brand-new bathtub as well as don't require to transform the plan of your previous supply of water pipes.
Your devices as well as material checklist need to consist of the following:
  • New Bathtub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Preparing for the Installment


    First of all, the supporting structure provided with the bath should be fitted (if needed) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is important to ensure that if the faucet includes a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps system to prevent stress on the bathtub.
    Fit the versatile faucet ports to the bottom of the two faucets utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
    Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now prepare to be suited its last position.

    Removing Old Taps


    If you require to change old taps with new ones as a part of your installation, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be quite problematic because of the limited accessibility that is frequently the case.
    Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a towel all set for the remaining water that will come from the pipes. When the supply pipes have actually been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. When the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing compound.
    Before proceeding to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.

    Setting up the Tub


    Using both wood boards under its feet, put the tub in the needed setting. The wooden boards are useful in evenly spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 little points.
    The next goal is to ensure that the bath tub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the bathtub until the level reads degree.
    To mount faucets, fit the bottom of the furthest flexible faucet port to the appropriate supply pipeline by making a compression join; then do the same for the various other tap.
    Switch on the water supply and also examine all joints and new pipework for leaks as well as tighten them if needed. Fill up the bathtub as well as likewise inspect the overflow outlet and also the typical outlet for leaks.
    Ultimately, take care of the bath paneling as described in the supplier's user's manual. Tiling as well as securing around the tub ought to wait until the bath tub has been used at the very least when as this will settle it into its final placement.

    Fitting New Taps


    If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipelines.
    If you need to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
    Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in area between the faucet as well as the sink. Secure the tap in position with the producer given backnut. When the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet ports. The previous type needs to be linked to the tap finishes first, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.

    Tiling Around the Tub


    In the location where the bath fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break an inflexible seal, creating the water to pass through the wall between the bath and also the tiling, causing difficulties with dampness and also feasible leaks to the ceiling listed below.
    You can choose from a range of coloured sealers to blend in your fixtures and fittings. They are sold in tubes and cartridges, as well as can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of drenched paper or soft rope. Keep in mind to always load the tub with water prior to sealing, to allow for the motion experienced when the tub is in use. The sealant can break relatively very early if you do not take into account this activity prior to sealing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise conveniently readily available on the marketplace. It is advisable to fit the tiles making use of waterproof or water-proof adhesive and also cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    As an enthusiastic reader on How to Install a Bathtub Yourself, I thought sharing that excerpt was smart. Liked our write-up? Please share it. Let other people discover it. Thank you for taking the time to read it.



    Schedule Now!

    Report this page